Hp 2530 mac based vlan

These instructions assume that CoovaChilli is installed on the access point. These instructions also assume that you have an SSID configured on the access point. You should also make sure to have a default route properly configured on the access point so that it can access the Internet and that DNS resolution is working. Please note that any interface name reference might be different from one equipment vendor to an other. Just make sure to follow these configuration guidelines and you should be all-set.

A startup script might be required depending on the equipment vendor. Again, a quick documentation search on the Internet might be the best solution to find the best one. Once set up, you might want to activate chilli at boot by using the startup script and finally, reboot the AP. On the bottom of the page, click the Add switch to group button then select the default to bring up the New Switch configuration modal window.

HP Procurve zl with Windows Radius NPS

It is required to disable HTTPS redirection by clicking the Configuration tab and then the Captive portal menu option on the left hand side. Make sure Secure redirect is unchecked. In order to have the Extricom controller working with PacketFence, you need to define two ESSID definition, one for the "public" network, and one for the "secure" network. Create the profiles per the following:. You will need to install wpad and hostapd. Go to the tab Available packages and then search for the package hostapd into the Filter: field.

You will need to modify the hostapd script that comes with the package that we previously installed. In order to apply this configuration, when you are connected using SSH on the AP, run the command wifi. It will reload the configuration and broadcast the SSID. If you want to debug, you can use the command logread. Configure a security profile named huawei-ap.

Set the security policy to WPA authentication, authentication method to In this section, we will cover the configuration of the Meraki controller to use Web authentication. Next, configure the roles for the devices on your network.

Creation of the policy Guest :. You will need to access the Meraki dashboard to configure your switch. When you reach it you will need first to create a policy. You can create a "MAC authentication bypass" or a " Depending if you want to authenticate user via dot1x or MAB. You cannot combine both neither use a fallback mode on the same port, each port with a policy applied will be exclusive to MAB or dot1x.

From there create a new policy, use the example below to create your policy. You now need to apply one of your policies to ports. To add a policy you created earlier, select it in the drop down list in Access policy. The only deauthentication method available is SSH, so create an account in the Mikrotik AP and fill the information in PacketFence switch configuration.

Step 2: Conenct PuTTY

In this setup we use the interface ether5 for the bridge Trunk interface and ether1 as the management interface. You can use webauth external captive portal on Mikrotik APs. In order to do so, you will have to activate the hotspot feature in the AP configuration as well as modify the redirection template so that it points to PacketFence. Next, in the login.


  1. Wired Intelligent Edge (Campus Switching and Routing);
  2. wireless gaming mouse g700 mac.
  3. n64 emulator keyboard controls mac?
  4. Subscribe to Blog via Email.
  5. hp photosmart 5510 driver mac os x 10.4.
  6. mac audio mpx 112 bp;

Now, you must configure the hotspot feature on your AP. This configuration is done on top of an existing SSID you have previously configured which is on interface wlan1. Adjust the interface name if needed. Next, you need to allow access to the PacketFence portal in the hotspot access list. Change Next, you need to configure PacketFence to use webauth for this Access Point using the following switches. This is true if you are running AP s using any 5. You can also add those commands to the AP bootscript. Contact your Meru support representative for that part. Here, we create our wireless security profiles for use.

Here, we create our SSID and tie it to a security profile.

J9772a warranty

Repeat those steps for the open and secure SSID by choosing the right security profile. Here, we tie our SSIDs to access points. When you add a rule, you have to pay attention to two things:. So, since the matching is done using the Firewall Filter ID configuration field, your roles line in switches. Add a new Wi-Fi profile with the following attributes:.

Disabling MAC address learning on a VLAN

First, we need to build the AAA Policy. Under Basic Configuration:. You have multiple options here. For the purpose of this document, we will modify the general profile. Here, we can configure our SNMP community strings. Again, you can modify the default one, or you can create a brand new Policy. You need to ensure that the uplink interface of the controller is configured as a trunk, and that all the necessary VLANs are created on the device. Ensure that the up1 interface is set as trunk, with all the allowed VLANs.

First create a global policy that will contain your roles. Next, create your Roles by clicking on the Add button on the bottom right. In the roles configuration in switches. Make sure also to commit the configuration upon your changes. The steps have been done using the CLI. Next, create or adjust your management policy to configure the SNMP traps. Here is an example policy, please note the two last lines:. Finally, you need to configure a radio interface on your AP to act as a sensor.

Here is an example configuration for a dual-radio AP Enter the proper configuration:. First, configure the controller to send the traps to PacketFence. Next, you need to configure the Alarm Settings. Finally, enable the WIPS feature on the controller. In order to use PacketFence as an external captive portal for web authentication, you will need to configure first your RADIUS authentication and accounting server see steps above.

Configure the Hotspot service profile to redirect devices to your PacketFence portal. On the ZoneDirector configuration in PacketFence, you will need to specify -1 as the registration VLAN in order to display the captive portal to the end device. To apply the configuration, restart PacketFence using the following command: service packetfence restart.

Introduction

Ruckus allows you to define roles. You can still limit access to certain WLAN. On the PacketFence side you need to use role by switch role and add the Group Attribute you created on the Ruckus side. In the case that the role is not allowed on the WLAN then the device will not be allowed to connect. Create your server using the following information where Adjust Then, still on this page, in the Walled Gardens , make sure you add the portal IP address in this list.

Also ensure you set Use the controller as a proxy. Keep the password closeby as it will be required for the PacketFence configuration. In order to configure web authentication external captive-portal on Ubiquiti access points, you must have access to a Unifi controller and your APs must be connected to it. First, you must configure the guest policy.

HP Procurve Switch 2626 configure VLAN

Once this is done, you will need to define all your APs MAC addresses in the PacketFence switches with a configuration similar to this:. There is a special case when you want to be able to deauthenticate a device when it is connected on the secure SSID.